sistervase7

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/oldham-emergency-boarding-up-near-me/

How to Go About Boarding Up a Door The protection of vacant investment properties from the elements is attainable by board up a door It may not prevent all damages but it can help to avoid some of the issues that are associated with severe storms The boarding of doors and windows can also deter burglars and vandals However it can be expensive and timeconsuming to install plywood boards over the openings of a property Measure the Door First youll require a tape measure You might want to keep a chair or ladder nearby in case you need to see more clearly the top of the frame Wear gloves and protective glasses in the event that you need to make use of these tools Start by taking measurements of the length of the door This can be accomplished by running the tape horizontally across the door Make sure to remove any extra door parts such as the door sweep to get this measurement Then determine the height from the floor up to the sill or the lintel It is essential to measure in multiple locations especially when measuring doors older than they may not have an exact rectangular shape If the measurements differ take the largest number After youve logged the width and height measurements and youll need to determine what size board youll need for the frame It should be at minimum 2 wider and 1 higher than the door 2 higher This will give you plenty of space to shim the frame and door to fit Its a good idea to remove the trim or casing around the jambs of the door in order to observe the studs This will let you determine the exact distance between the frames studs and the edge After you have removed the trim measure the length of your door frame using the tape measure The frame should be measured at three different places and then use the most compact measurement Also you should take measurements of the frames height from top to bottom on both sides Use the shortest measurement to determine the width of your door If youre having difficulty with these measurements its best at this point to consult an expert and ask them to visit your home to do the measuring for you Theyll tell you the dimensions and what kind of door you require and how to prepare your frame to accommodate a replacement door Cut the Plywood A door frame is usually made of a series of studs or boards that create a hollow space around the door Two hinges are attached to the studs and keep the door in position This means that if you need to refinish the door it is important to remove the door from its hinges for a night Placing plywood into the door opening is an easy method to board a door and prevent insects from getting into your home It is simple to do without having to nail or screw the plywood to the door frame Plywood is cheap easy to work with and looks great when it is completed repairmywindowsanddoorscouk is the ideal material to make a temporary solution for a problem where youre required to remove an existing door in order to refinish it or put in the new one It can also be used to secure the opening of a space being renovated such as a basement or construction site For a wall constructed of plywood start by taking measurements of the width and height of the door opening Mark the dimensions on the plywood using an utility knife and an drywall square or any other straight edge made of metal Then snap an outline of chalk across each line to indicate where you want to cut Utilize a circular saw to cut the plywood to size It is crucial to protect both your eyes and ears when cutting plywood Wear earplugs or protective goggles whenever possible It is also important to use a blade with a lot of teeth which will permit you to cut quickly and with little tearout Make use of a small piece wood to guide the blade Keep it a hairs distance from the mark when cutting Attaching a pair or short braces at each end is a good way to secure the plywood in place without screwing it into the studs Place one brace on the inside and the other outside of the door Position a pair 112inch deck screw in each hole and then tighten by using an openend ratchet Fasten the Plywood Its now time to connect the panel to the frame once you have the plywood sheet cut to the correct size and the holes for rails and stiles of the door frame are predrilled This is a simple project that does not require a lot of carpentry expertise so long as you follow the correct procedures and use the right tools Start by setting up a table near the doorway with two sawhorses as well as 2by4 framing lumber at each end of the table Lay the entire sheet of plywood flat atop the sawhorses using the marks from the measurement process to guide you to cut Utilize a utility knife and a straight edge made of metal to cut the lines This will create a guideline for the saw blade and will help prevent splintering when you cut the plywood Wear eye protection and use a circular or table saw equipped with a finetoothed blade cut along the line of scoring Sand the edges of the panel using 120grit paper to smooth it out and eliminate any burrs After the sanding apply a layer of wood sealer to the plywood panels and let dry as directed by the manufacturer Install the hinges on the door frame If youre using a Thinge make holes in the exterior face of your door for the straps portion of the hinges Then place the hinges outside face on its mark and screw it to the frame with a screw gun Repeat the process for each hinge on the inside of your door Be cautious not to tighten them too much or the panel could shift If you have a single Thinged outside door you can make it easier for the latch to close by placing wire through the loops of the outside hinges Bend a short piece of tie wire in half and put it through the two holes on the outside of the door then twist the wires together to pull them tightly and fix the door Install the Plywood Based on the measurements you have taken place the plywood in the door opening Adjust the header top of the frame and the sill bottom Use a level to be sure theres not any slop in the header or sill If the level isnt perfect put another shim where you need it and repeat the process until you get the sill and header to be plumb Once the plywood is in the frame secure it with stainless steel hinge bolts and wing nuts Make use of a screwgun that has an attachment for hex heads to avoid removing the heads of the screws If you live in a house with studs that run along the length of your doorway you can drill hanger bolts into each framing member This is a far easier job than making the hole using the aid of a saw for drywall After putting the plywood in place after installation take measurements of the width and height of your door opening If needed trim the plywood bottom to be a little higher than the height of your door frame Cut two pieces of framing wood 1by6 to serve as braces for the upper and lower ends Cut along the lines that are marked on your plywood using circular blades with finetoothed teeth Wear eye protection Remove any splinters from the cuts by using an sanding block Once you have the braces in place nail each one to the plywood with pairs of finishing nails 2 inches long Counter sink all the nail heads once youre done Seal the braces with a quality wood sealing product such as the wipeon polyurethane from Minwax If the door is too big it is possible to add decorative molding to fill in the space between your door and jamb or you can resize your opening In most instances however it is less expensive and simpler to purchase an entirely new door This will also take away any issues you might have had with the original door if it was damaged and didnt suitable for the opening