mealmen22

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/watford-windowrepair/

Replacing uPVC Window Handles It is simple to change the handles on windows made of Upvc The most important thing is to make sure that the replacement handle fits the spindle cut out in the window mechanism If the steps below are followed correctly any cockspur handle should be able to fit into most windows The height of the step of the handle is important What to look for As time passes uPVC handles on many windows in the UK begin to show signs wear and wear and tear When this occurs the handle could become shaky or difficult to operate making it essential to replace it Anyone who is proficient using a basic hand tool is able to complete this task The first thing to do is make sure that the handle is securely attached to the window frame and is in the open position The next step is to locate the screws or pins which hold the handle They are usually on the inside of the handle and can be removed with a screwdriver or pliers Once the handle is loose and sagging it can be removed from its hinges by gently pulling it off It is then time to find a new handle with the same design and size This can be done online or in an area DIY store and should take about five minutes with the help of a screwdriver The most important thing to consider when replacing the uPVC window handle is its step height This is the distance from the base of the handle to where it is placed on the window frame It is generally an accepted measurement however it is important to examine the step height of your existing handle prior to ordering a new one Depending on the type of handle you have there are various sizes that are available Inline handles are offered for uPVC window with lug centres of 31mm while cockspur handles have lug centres of 43mm Tiltandturn handles are commonly found on uPVC Windows They have a special design that lets the window be tilted to allow for ventilation and then turned to fully open the window The most frequent breakage in uPVC handles is that they crack internally instead of breaking away from the base section This could make it difficult to open It is essential to make sure that any replacement handle has the same spindle that was used in your original one Remove the old Handle A poorly installed or damaged window handles may cause your doubleglazed windows to open and close incorrectly and can result in them becoming stuck There are a myriad of reasons like general wear and tear or corrosion of the metal handle In these instances it is crucial to replace the upvc window handle as promptly as you can to avoid further damage or loss of functionality When replacing the handles of windows made of upvc it is recommended to remove the old handles from the window To do this begin by getting rid of the screw that is covered when the handle is in the closed position This should reveal another screw that once removed you can then begin to remove the handle itself It is recommended to employ an electric screwdriver to accomplish this since it will make the task easier and quicker It is also important to note that the screws on the handle may be hidden behind caps made of plastic so it is recommended to take a Stanley knife to the screw covers and remove them After the old handle has been removed you should then look at the square cut on the handles base to make sure that the new window lock handles are compatible with it It is essential to measure the spindle length on the old handle and compare it to the size of the window mechanism spindle cutout There are three kinds of Upvc handles Espag handles with a central screw that can be turned either left or right and Cranked handles that have two screws and Spade handles that are made of flat arms and can be used either side of the upvc window When you have a suitable replacement its just a matter of screwing the handle in place and ensuring that the spindle is correctly inserted into the lock mechanism Once this is done the handle should be secured to the window frame and your new window handles made of upvc must be secure Measure the Spindle If you have to replace a handle made of upvc that has fallen its likely that the spindle holding it in place is damaged or loose In some instances it can be fixed using screws or pins to tighten it In certain situations it is necessary to replace the handle There are a few different kinds of window handles made of upvc Repair My Windows And Doors include espagnolette handles that are inline as well as cockspur handles tilt and turn handles Each kind has a distinct method of installing and removing the handle Before you purchase a new handle it is important to know the size of the one you have This will help ensure that the new handle is the correct size and fits into the window Fortunately all handles adhere to industry standards of sizing making it quite easy to locate the right size To determine the size of your handle first remove it from the window by turning it back to the open position You will then be able see the size of the screw or pin that secures it Make use of a ruler or tape measure to determine how long the spindle is Once you have determined the length of the spindle you can purchase a replacement one that is exactly the same size When you are looking to replace a handle it is important to take into consideration the step height of a window handle made of upvc The step height is measured from the base to the point at which the handle is positioned on the frame In general this is about 21mm for uPVC windows and 9mm for aluminium To ensure that the new handle will work you can drop something into the space to check how far it extends before it meets an obstruction Cockspur handles often have different backset heights depending on the style of window they are installed in Inline Espag handles come with a standard height of 43mm from centre to centre 2 fixing points Cockspur handles however have different backset heights dependent on the design of the window they are in This is because they have a spur that extends from the handle and then locks over a cockspur wedge striker plate Fit the New Handle If youve decided to replace the handle make sure you align it to the screw holes in the door and fix it using the screws provided If youre replacing the latch lever it can be put in similarly to the main door handle Then you can reattach the door trim in order to conceal the mounting screws and finish the job Tip To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the floor Then you can use a hammer and tap the thin end Be careful not damage the handle or the spindle