hateemery17
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.repairmywindowsanddoors.co.uk/southend-window-lock-repairs-near-me/
How to Do a Door Lock Change Changing your door lock is an easy and affordable way to improve the security of your home The process is not for everyone It requires a certain amount of patience and skill The cylinder is inside the knob body The cylinder is responsible for recognizing the key when it is inserted in the lock Remove the old lock The first step is to remove the old lock Its a relatively simple process but it is important to keep certain things in your mind Make sure that the new lock is compatible with your door This will ensure that it fits securely and does not leave a gap in the deadbolt plug or latch After removing the latch plate you will have to look for two bolts or screws on the inside of the casing which are holding the casing in place with the lock halves Unscrew them using a screwdriver then pull the lock out of the door If you have a mortise locking mechanism there is an anchor screw that connects the handle to the spindle Use RepairMyWindowsAndDoors to unscrew this screw then remove the doorknobs You should also remove the latch and deadbolt plug from the hole in the door jamb Install the new lock If you are replacing a mortise you should take a measurement of the distance between the lock case and your doors edge to ensure that the new lock will fit There are a variety of reasons that could prompt you to replace the door lock including being concerned that someone else may have the key or you are welcoming a new roommate In any case you can save money by removing the lock yourself rather than hiring a professional to do it It is much easier than you think and can be completed in just a few moments Remove the handle and trim of your door With a flat screwdriver remove the trim You should be able to twist off the majority of it In certain cases you may even be able to take off the handles completely Then check the handle for a tiny hole on the inside and insert a straightened paper clip into it This will trigger the release mechanism and allow you to take the handle from the door Look for a small tab that is located inside of the lock and press it using a flat screwdriver After the spindle is removed you can take off the cylinder and housing Selecting a new locking system When it comes time to pick a new lock there are a lot of choices Think about the various kinds of locks and select one that matches the design of your door Consider the backset which is the distance between the edge and the middle of the hole for the lock Also consider the cross bore a tiny hole that is located at the edge of your doors frame Select a lock that will fit the door thickness and the swing The American National Standards Institute and BHMA have graded most locks for doors to give you an idea of their durability and the difficulty to pick them or disable them A grade 3 lock might be ideal for a quiet suburban apartment complex whereas a grade 1 lock might stand up to the traffic that is frequented by a storefront on a busy city street Most smart door locks require a digital code to open If youre concerned about security breaches or hacking seek out a professional locksmith or your local police department for assistance Replace the cylinder If your door lock cylinder is broken or damaged you can replace it within a matter of minutes using a simple DIY project The trick is to select the right cylinder and follow the directions that come with it First take off the knob or handle if it is present Then using a screwdriver unscrew the trim that surrounds the lock cylinder After the trim is removed you can remove the screws holding the cylinder in place using a flathead The cylinder is then gently lifted out of the door Before installing the new cylinder be sure that its the right length for your door With a tape measure measure the distance between the cylinders center and its right and left sides Purchase a new cylinder which has the same measurements This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside Place the replacement cylinder inside the door and then turn the key This will ensure that the cylinder is aligned with the carrier which is usually located on the outside of the lock Then loosen the set screws which should be just a couple of turns inside the head If there is a screw at the edge of the case that is holding the door youll need to remove it After removing the lock cylinder you can replace it with a new lock by sliding the new cylinder into the case and tightening the set screw It is also recommended to reinstall the bracket that connects the cylinder to the lock indicator stem and this can be done by removing three tabs on the back of the cylinder using needlenose pliers Then you can connect the smaller bracket to the back of the cylinder Then you need to reinstall the strike plate and latch plate as well as the retaining ring attached to the top of the lock the cylinder Installing the new lock Start by measuring the doors width if are replacing an existing lock Most residential locksets come with a thickness of 38 to 1 34 inches If your door is more thick it will require a thick door kit that includes longer screws and an extended tail piece for door knobs or spindle extensions for deadbolts Most locks come equipped with a detailed installation guide to help you Take the time to read the instructions prior to beginning the process to make sure that you are following all the steps The guide will give you a good idea of the level of skill that is required to complete the task If youre changing a lock for the first time you might consider asking a more experienced friend for assistance Before installing the new lock it is recommended to tape over the openings of the old hardware This will prevent the screws from slipping through the holes and also protect any tiles you might have installed It also shields your tiles from any damage caused by rust dirt and grime SECURAM Touch includes the masking strip or gaffer tape However you can use any tape you have After removing the screws that hold the locks interior to the exterior and take the lock off immediately Its crucial to do this swiftly to avoid the lock from closing itself in a way that could end up harming the mechanism If your new lock is equipped with an internal latch bolt insert the new bolt into the upper cross bore Make sure you place it in the right position which is usually marked by an arrow on the faceplate Then screw the latch plate onto the bolt Screw the deadbolt to the jamb on the door Test the deadbolt a few times throwing it around to make sure it extends into the strike plate Follow the directions that come with your electronic smart lock to program it This requires downloading an application registering your email address confirming your identity and connecting to the wireless network in order to connect your device
