diggerjar29

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/walsall-window-lock-repairs-near-me/

Reasons to Change Door Lock You can change your door lock for a variety of reasons from improving the security of your house to redecorating the entrance You may also need to change locks if your key gets stuck in the lock or is difficult to turn The process of changing your lock is a straightforward project that even beginner DIY homeowners can tackle To begin gather the necessary materials Remove the old lock Removal of the lock that was previously installed from the door is an essential step prior to installing the new lock This is particularly important if you suspect that someone else has a key to your home It may also be a good idea if you have moved into a house that was burglarized or welcomed a new roommate Its much more simple than you think and can be done in a matter of minutes Start by removing the screws holding the deadbolt faceplate on the frame of the door To remove the faceplate youll have to remove screws from both sides upvc window locks repair will allow you see the hidden screws and provide you with an understanding of how to continue with the rest of steps After you have removed the old faceplate youll need to remove the bolt and strike plate Use a screwdriver or a wrench to loosen the bolt and remove it from the hole in the door If the bolt is rusty you may need to use a chisel to remove it If youre using a chisel be careful not to scratch the door frame Make sure your new doorknob deadbolt and lock will fit in the holes already in the door before you take out the old one A lot of hardware stores and big box stores stock a range of locks and will assist you in choosing the right one If the lock you purchased does not match your door bring it back and seek assistance While youre taking off the lock that was previously in use look for small depressions or notches in the handle or around the trim If you can locate them insert a straightened safety pin or a flat screwdriver through them to open the handle and expose the screws beneath After you have removed the screw from the handle you are able to start removing the knob To do this locate the set screw that is located on the knobs base and loosen it Then remove the spindle Install the new lock It is a good idea to change the locks on the doors of your home regularly especially in the event of a burglary or you move into a new home with roommates It is easy cheap and effective to change the lock on your door The majority of people can do this themselves with a screwdriver and some basic directions Based on the situation you may also need to learn how to reset a lock so that only you own the key Youll need to buy a new lock with the same keyway as your current lock Most locksmiths will replace your lock at an additional cost but you can save money by doing it yourself You can purchase an entirely new lock from a hardware store or on the internet A standard deadbolt will typically fit on all doors however youll have to measure the area on your door to make sure that it will fit The lock you buy will typically come with a template showing how to install it on the door This template can be used to drill the hole Its much simpler than having to measure every time If the template doesnt line up with your hole you should take it back to the hardware store to purchase another one When you install the new lock ensure that it is placed on the right side of the door You can confirm this by checking the latch which should be marked up or something similar Make sure the latch is sitting correctly in the latch plate then secure it using the screws supplied If you are replacing a door knob lock Its important to be aware of the handing Certain knob locks are lefthanded If youre not careful the lock could be installed on the wrong side of your door which could prevent it from being locked from the inside or outside It is recommended to try the new lock after you have completed You should be in a position to lock the door from both the inside and the outside and unlock it with a key If youre not satisfied with the results you can always contact a professional locksmith to fix it Test the lock A lock that does not unlock can be annoying however it could also put your familys safety at risk Luckily its easy to fix most problems with door locks by performing a bit of troubleshooting and lubrication First ensure that your key is properly cut and that the lock itself isnt loose or dirty If this does not solve the issue try lubricating your door lock actuator with graphite powdered Ensure that the doorlock switch wiring harnesses and actuator connectors all function properly Check the wiring diagram or manual to determine the color code and function of each wire of the door lock switch Then test the wires using a light or digital meter to see whether the door locks actuator is receiving power and ground when the switches are activated If you notice the switches switch on and off with voltage it means the switches are in good shape and the actuator will require replacement If the switch seems to be working but the actuator doesnt move when you turn the knob it could be a problem with the actuator cylinder itself The actuator cylinder has springloaded pins that stop the cylinder from rotating until the key is placed in and moves the pins upwards to accommodate the height of the key in that location Then the cylinder to spin and open the lock body which allows the handle to latch If your door lock actuator is malfunctioning you can take the switch and wires from the actuator with small screwdrivers to unlock the bolt that locks and then separate the plastic cover that houses the electrical connector Then disconnect the door lock actuator and let it fall Then you should be able find and remove the two bolts that are that hold the actuator in position Once the actuator has been removed then you can disconnect the black electrical connector Replace the key If your deadbolt is locked or door knob isnt functioning youll have to rekey it or replace it This is not difficult and will save you money It is recommended to have an expert locksmith inspect the locks for any issues before you start This will give you peace of heart that your home is safe and secure To begin remove the faceplate that is on the outside of the deadbolt or doorknob If there are screws that hold the faceplate in place use a screwdriver and remove it Then remove the interior faceplate using a flathead screwdriver Once you have removed the faceplate you are able to remove the bolt and screw from the lock cylinder A locksmith can determine if you need to replace or rekey your lock They can also advise you about the best security options for your home They can also make the necessary adjustments to your door and frame for a perfect fit They also provide an assurance on their work You will need to purchase a brand new lock key before you are able to reset it It is crucial to select the lock key that fits snugly A key that is not properly fitted could cause damage to the mechanism inside and stop it from functioning To test the size of a key simply insert it into the lock If it is flush with the plug its of the correct size If the pins protrude from the top of the plug then they are too long You might want to replace your door lock for a variety of reasons such as If youre moving into an owners home or if you lose your keys rekeying the lock could be a more affordable alternative than replacing it Its also less invasive than a complete replacement Rekeying an existing lock may not be feasible in some circumstances For instance if your lock is damaged or has been jammed repeatedly its likely the time to replace it