damagefile77

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/colchester-window-lock-repairs-near-me/

How to Do a Door Lock Change Door lock replacement is a quick and cheap way to improve your home security The process is not for everyone It requires a certain amount patience and skill The cylinder is contained within the knobs body The cylinder is responsible to recognize the key when it is inserted in the lock Take off the lock that was previously used The first step to replace a door lock is to remove the old one Its a relatively easy process but it is important to keep some things in your mind First make sure that the lock you choose to install is the right size for the door you have This will ensure it is securely fitted and wont create a gap around the latch or deadbolt After you have removed the latch plate you will be required to search for two bolts or screws on the inside of the casing which are holding the casing together with the two halves of the lock Remove these screws with a screwdriver before removing the lock off the door If you have a mortise lock there could be a set screw at the base of the handle that binds it to the spindle Make use of a screwdriver for removing this screw then remove the doorknobs Remove the deadbolt and latch plug from the door jamb Install the new lock If you are replacing a mortise lock you should also determine the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit There are a variety of reasons that could prompt you to replace the door lock such as being concerned that someone else may have the key or if youre welcoming an incoming roommate You can save money by deciding to remove the lock yourself instead of hiring an expert It is much easier than people think and can be completed in just a few moments Begin by removing the handle and trim from the door With repairmywindowsanddoorscouk remove the trim You will be able to pull off the majority of it and in some cases the handles may fall off completely The next step is to look for a pinhole on the inside of the handle and insert an unstraightened clip into it This will activate the release mechanism which allows you to remove the handle Then look for another small tab on the interior of the lock and press it with a flat screwdriver After the spindle is removed you are able to remove the cylinder and the housing The choice of a new locking system When it comes to choosing the right lock for your home you have many choices Think about the various kinds of locks and select one that is in keeping with the style of your door Consider the backset which is the distance between the edge and the middle of the hole for the lock Also consider the cross bore which is a small hole at the edge of your doors frame Select a lock that is suitable for the door thickness and the swing The majority of door locks are assessed by BHMA and the American National Standards Institute to give you an idea of how they stand up to use and how difficult to pick or disable A grade 3 lock might be ideal for a quiet rural apartment complex while an entry grade lock could be more able to withstand the traffic at a busy store front on a city street Most smart door locks require a digital code to open If youre worried about hacking or other security concerns seek out a professional locksmith or the local police department for advice Replace the cylinder It is easy to replace damaged or broken doors lock cylinder using a simple DIY project It is crucial to choose the right cylinder and follow the instructions First take off the knob or handle if it is present Then using a screwdriver remove the trim that is around the lock cylinder Once the trim has been removed you can access the screws that hold the cylinder in place and remove them with the flathead screwdriver The cylinder is then gently pulled from the door Before installing the new cylinder be sure that it is the correct length for your door Measure the distance from the center to the left and right sides of the cylinder with an instrument Purchase a new cylinder that has the same measurements This will stop cylinders from snapping when doors are hit or the key is stuck inside Once you have a suitable replacement cylinder put it in the door and turn the key This will align the cylinder with your carrier which is located usually on the outside of the lock Then you can loosen the set screw which should be just a few turns in the head Also you will need to loosen the screw at the edge of the door that fastens the case should there be one You can replace the old lock cylinder with a new one by slipping it into the case and tightening the set screws Reinstalling the piece that connects a cylinder to a lock indicator stem is also essential This can be done by pulling three small tabs in the back of the cylindrical with needlenosed pliers Attach the bracket that is smaller to the back of the cylinder Then you must put back in the strike plate and latch plate as well as the retaining ring that is connected to the top lock cylinder Installing a new lock If youre replacing an existing lock start by measuring the width of the door Most locksets for residential use are designed to fit a door thickness of 1 38 34 inch If your door is more than 1 38 to 1 34 inches youll need an extra thick door kit This will require longer screws as well as a longer spindle extension or the tail piece for door knobs Most locks come with a detailed installation guide to assist you Be sure to read the instructions thoroughly before starting the process to make sure that youve followed all of the necessary steps The guide will also provide you with an idea of the level of skill required to perform the task If youre replacing a lock for the first time you might consider asking a more experienced person for help Its a great idea to cover the holes in the old hardware prior to installing the new lock This will stop the screws from falling out of the holes and protect any tile you might have installed in the area It will also prevent any potential damage from rust dirt and grime SECURAM Touch comes with a strip of masking or gaffer tape however you can make use of any tape you have After you have removed the screws that hold the locks interior to the exterior then pull the lock straight away This should be done swiftly to avoid the lock from closing accidentally and damaging the mechanism If your new lock has a latch bolt fit the new bolt into the upper cross bore Make sure that you place it in the correct location which is indicated by an arrow Then slide the latch plate onto the bolt and screw it into the correct position Finally screw in the deadbolt and strike plates to the door jamb Try the deadbolt a few times by throwing it to see if it extends into the strike plate If youre using an electronic smart lock be sure to follow the included instructions for programming it This involves downloading an application entering your email address verifying your identity then accessing the wireless network to add your device