codweek86

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/peterborough-emergency-boarding-up-near-me/

How to Go About Boarding Up a Door The act of boarding up a door is one way to protect vacant investment properties from the elements While it wont stop all destruction it can help avoid some of the problems that come with severe storms The idea of boarding up doors and windows can deter trespassers vandals and squatters Placing plywood boards over doors and windows can be timeconsuming and expensive Measure the Door The first thing youll need is a tape measure You might want to keep a ladder or chair close by in case you require to see more clearly the top of the frame If you must use these tools be sure to wear gloves and safety glasses Once you have the measuring tool begin by taking the doors width measurement This can be done by running the tape horizontally across the door Make sure to remove any other door components like the door sweep from the measurement Then determine the height measurement by measuring up from the floor to the current sill plate or lintel It is important to measure multiple locations especially with older doors because they may not be a perfect rectangle If the measurements are different use the largest figure After youve taken the width and height measurements and youll need to figure out what size boarding youll need to fit into the frame Ideally it should be 2 inches greater than the doors width and 1 inch thicker than the door 2 higher This will allow plenty of space to shim the frame and door into place When youre ready to take the door frames width and height measurements Its a good idea to remove any trim or casing from around the door jambs so that you can see the studs that are behind them This will allow you determine the exact measurement of the space between the studs and the edge of the frame After youve removed your trim youll be able to measure the size of the frame of your door by running the tape measure across the entire frame in three places and using the smallest measurement to determine the width of your door It is also important to measure the frames height from top to bottom on both sides Make use of the shortest measurement for the width of your door If youre having difficulty with the measurements you should get a professional to your home and take the measurement Theyll be able tell you exactly what type and size of door you need and the best way to prepare the frame for the new door Cut the Plywood A door frame is typically composed of a series of thin boards or studs which create a hollow space around the door The typical door is held in place by two hinges that are fixed to the studs If you want to refinish the door youll have to remove it from its hinges overnight To keep insects out of your home and to secure the door opening a simple method to board doors is to place plywood in the opening It is simple to do without having to screw or nail the plywood to the frame of the door Plywood is cheap easy to work with and looks stunning when completed It is the perfect material to make a temporary solution for situations where youre required to remove the door you have in place to refinish or install an entirely new one It can also be used to secure the opening of a room being transformed such as an excavation site or basement For a wall constructed of plywood start by measuring the width and height of the door opening Draw the measurements on the plywood with the help of a utility knife a drywall square or another metal straight edge Then you should snap a chalk line across all the lines marked to indicate where youll need to cut Finally utilize circular saws to cut out the plywood to size It is crucial to shield your ears and eyes when cutting plywood Wear protective goggles or earplugs if possible It is also important to use a sharp blade with a lot of teeth which will allow you to cut quickly and with little tearout Make use of a small piece wood to guide the blade Hold it about a hairs width away from the line you are cutting An effective way to hold the plywood in place without screwing it to the studs is to attach braces that are short at each end Set one brace on the side of the door and the other on the outside Place a 112inch deck screw in each hole and then tighten with an openend ratchet boarding up services s now time to connect the frame to the panel after you have the plywood sheet cut to the correct dimensions and the holes for rails and stiles of the door frame are predrilled This is a simple task that doesnt require any advanced carpentry skills if you have the right tools and follow the right steps Set up a table in the entrance with two sawhorses at each end and framing lumber 2x4s Utilize the marks you made during the measurement procedure to guide you in cutting the plywood Mark the lines using the help of a utility knife a drywall square or other metal straight edge This will serve as a guide for the saw blade and prevent splintering of the plywood when cutting it Wear eye protection and use a circular or table saw with a finetoothed blade to cut along the scored line Sand the edges of the panel using 120grit paper to smooth it out and eliminate any burrs After sanding the plywood panels apply a wood sealer and allow it to dry according to the manufacturers instructions Install the hinges on the door frame If you are using a T hinge you need to drill holes through the outer face of the door to accommodate the strap parts of the hinges Then you can screw the hinge on the outside to the frame with a screwdriver Repeat the process on the inside of the door for each of the hinges remaining but be cautious not to tighten too much on any of them or the door will shift If you have a single Thinged outside door it is possible to make it easier to close by putting wire through the loops of the exterior hinges Fold a short piece to tie wire in half and then fish it through the two holes on the exterior of the door Then twist the wires together and fix the door Install the Plywood Install the plywood in the doors opening using the measurements that you took Change the header of the frame top and the sill Utilize a level to make sure theres not any slop in the header or sill If the level isnt perfect then put a second shim in the area you need it and repeat the process until you get the sill and header to be level Once the plywood is set secure it with the stainlesssteel hinge bolts and wingnuts Its a good idea to utilize a screw gun that has an attachment for a hexhead to keep the head from being stripped of the screws If your home has studs that run along the length of your doorway you can drill hanger bolts into each of the framing members This is much simpler than using a drywall saw to make the hole After installing the plywood measure the width and the height of the door opening If necessary cut the bottom of the plywood to fit the size of the door frame Cut two pieces of 1by6 framing lumber to form braces that connect to the upper and lower ends of your door Cut along the lines marked on your plywood using circular blades with teeth that are finelytoothed Wear eye protection Splinters can be removed from the cuts using a sanding tool Once youve got the two braces in place attach each one to the plywood with a pair of finishing nails that measure 2 inches Counter sink all nail heads after youve finished Cover the braces and plywood with a highquality wood sealer such as this wipeon polyurethane by Minwax If your door is too big you can either add decorative molding to fill the space between your door and jamb or you can resize your opening However in many cases its cheaper and easier to simply choose a new door It also eliminates any issues you might have encountered with your doors original model if it was damaged or not suitable for the opening